Source: https://mokxi.com/ideas/esp32
Updated: 2026-11-17

Projects / Project ideas
Project ideas by board

# ESP32 project ideas

124 Mokxi projects run on an ESP32 (55 beginner, 50 intermediate and 19 advanced). Here are 24 to start with, from “MicroPython DHT sensor: temperature and humidity” to “Stacker”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “LOLIN32 Lite button”, a beginner project that needs a push button.
- Most of them are beginner projects. Pick one a level below what you think you can do, finish it, then move up.
- The parts used most here are the LED (43 projects), the push button (19) and the potentiometer (11). With those on hand, most of this list is open to you.
- An ESP32 runs at 3.3 V. A 5 V sensor output needs a divider or a level shifter before it reaches a pin.

Projects

## 24 projects of 124

### MicroPython DHT sensor: temperature and humidity

MicroPython on an ESP32: the dht module reads a DHT22 on GPIO 13, with a 10k pull-up, and prints temperature and humidity every two seconds.

Board

ESP32-DevKitC V4

Parts

DHT11 or DHT22 sensor, resistor

Level

Beginner

Open in the simulator

### CYD hello

The Cheap Yellow Display writes on its own 2.8 inch screen with TFT_eSPI, set up as the board is wired, and cycles its RGB LED.

Board

Cheap Yellow Display (ESP32-2432S028R)

Parts

Just the board

Level

Beginner

Open in the simulator

### XIAO S3 knob

The XIAO knob circuit on the ESP32-S3: D0 is A0 on GPIO 1, and the count is printed as the converter gives it.

Board

Seeed XIAO ESP32-S3

Parts

Potentiometer, resistor, LED

Level

Beginner

Open in the simulator

### Nano ESP32 blink

The Nano ESP32’s orange LED on D13 and its RGB LED, whose red, green and blue light in turn when their pins go LOW.

Board

Arduino Nano ESP32

Parts

Just the board

Level

Beginner

Open in the simulator

### T-Display hello

The TTGO T-Display writes on its 135x240 screen with LilyGO’s TFT_eSPI setup and counts presses of its two buttons.

Board

LilyGO TTGO T-Display

Parts

Just the board

Level

Beginner

Open in the simulator

### ESP32-S3 rainbow

The DevKitC-1’s own RGB LED walking around the color wheel, one WS2812 frame from the RMT every 20 ms.

Board

ESP32-S3-DevKitC-1

Parts

Just the board

Level

Beginner

Open in the simulator

### DevKitC blink

An LED on GPIO 2 of Espressif’s ESP32-DevKitC V4, which has no user LED of its own and covers the breadboard’s whole width.

Board

ESP32-DevKitC V4

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### ESP32-C6 fade

Breathes an LED on GPIO 10 with analogWrite, so the waveform comes out of the LEDC hardware and the core sleeps between steps.

Board

ESP32-C6-DevKitC-1

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### LOLIN32 Lite button

A pushbutton on GPIO 4 lights the LOLIN32 Lite’s blue LED on GPIO 22, which comes on when its pin is LOW.

Board

Wemos LOLIN32 Lite

Parts

Push button

Level

Beginner

Open in the simulator

### SuperMini blink

The blue LED on GPIO 8 lights when the pin is low and an LED on GPIO 2 when it is high, on the smallest ESP32-C3 board.

Board

ESP32-C3 SuperMini

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### D1 R32 button

A button on the Wemos D1 R32’s D2 hole, which is GPIO 26, lights an LED on D3, GPIO 25, and the blue LED on GPIO 2.

Board

Wemos D1 R32

Parts

Push button, resistor, LED

Level

Beginner

Open in the simulator

### XIAO C3 knob

A potentiometer on D0 dims an LED on D10, using the XIAO’s own pin names rather than the chip’s GPIO numbers.

Board

Seeed XIAO ESP32-C3

Parts

Potentiometer, resistor, LED

Level

Beginner

Open in the simulator

### SSD1306 OLED on an ESP32 with MicroPython

MicroPython on an ESP32 DevKit: machine.I2C on D22 and D21 and micropython-lib’s ssd1306.py draw text and a counter on an SSD1306 OLED.

Board

ESP32 DevKit V1

Parts

SSD1306 OLED display

Level

Beginner

Open in the simulator

### Freenove WROVER on its extension board

The Freenove ESP32-WROVER plugged into its GPIO extension board on a breadboard, blinking an LED from GPIO 2 through a resistor.

Board

Freenove ESP32-WROVER

Parts

Freenove ESP32 GPIO extension board, resistor, LED

Level

Beginner

Open in the simulator

### ESP32 async web server: BME280, slider and relay

ESPAsyncWebServer serves a page with BME280 temperature, humidity and pressure, a slider that dims an LED and a button that switches a relay.

Board

ESP32 DevKit V1

Parts

BME280 weather sensor, resistor, LED, relay module, DC jack and adapter, +1 more

Level

Intermediate

Open in the simulator

### ESP-NOW button and LED

Two ESP32s and no wire between them: the button on one sends on or off over ESP-NOW, the other lights its LED and prints each message.

Board

ESP32 DevKit V1

Parts

Push button, resistor, LED

Level

Intermediate

Open in the simulator

### WiFi: fetch the weather

HTTPClient against a simulated origin, with the numbers on a dial in the Cloud panel, and a request to the real internet that is refused.

Board

ESP32-C3-DevKitM-1

Parts

Just the board

Level

Intermediate

Open in the simulator

### API lab: fetch JSON

Call an API with normal HTTPClient code, edit its JSON response in Cloud and inspect the complete request and response.

Board

ESP32-C3-DevKitM-1

Parts

Just the board

Level

Intermediate

Open in the simulator

### Binary clock

An ESP32-C3 writes the hours, minutes and seconds as three rows of binary lamps on a 128x64 OLED.

Board

ESP32-C3-DevKitM-1

Parts

SSD1306 OLED display

Level

Intermediate

Open in the simulator

### MicroPython meteor light on eight PWM bar segments

MicroPython on an ESP32: eight segments of an LED bar on PWM pins, a bright head with a fading tail that sweeps up the bar and back.

Board

ESP32-DevKitC V4

Parts

10-segment LED bar graph, resistor

Level

Intermediate

Open in the simulator

### LED strip controller

Sixteen WS2812B pixels with on, off, brightness, color and two effects, faded between, from two buttons and a knob on the strip or from the Web tab.

Board

ESP32-C3-DevKitM-1

Parts

Potentiometer, push button, WS2812 NeoPixel LEDs

Level

Intermediate

Open in the simulator

### Pong, two buttons

A TFT paddle game on an ILI9341 screen, full screen at forty frames a second, played with two buttons.

Board

ESP32-C3-DevKitM-1

Parts

ILI9341 TFT display, push button, piezo speaker

Level

Advanced

Open in the simulator

### ESP32-C3 Simon

Four LEDs flash a growing sequence, four buttons play it back.

Board

ESP32-C3-DevKitM-1

Parts

Resistor, LED, push button

Level

Advanced

Open in the simulator

### Stacker

The arcade stacker game on two cascaded MAX7219 matrices: the row slides, the button drops it, the overhang is cut off.

Board

ESP32-C3-DevKitM-1

Parts

Arcade button, MAX7219 8x8 LED matrix

Level

Advanced

Open in the simulator

See all 124 ESP32 projects on the templates page

Keep going

## Wiring, libraries and more ideas

The ESP32 DevKit V1 board page Every project ideas list

### Wiring guides

- LED to Arduino Uno
- push button to ESP32
- push button to Arduino Uno
- potentiometer to ESP32
- potentiometer to Arduino Uno
- WS2812 LED strip to ESP32
- WS2812 LED strip to Arduino Uno
- buzzer to ESP32

### Library pages

- TFT_eSPI library
- Adafruit GFX library
- DHT sensor library
- Adafruit GC9A01A library
- Adafruit NeoPixel library
- XPT2046_Touchscreen library

### More project ideas

- Arduino Uno project ideas
- LED projects for Arduino, ESP32 and Pico
- Projects with a push button
- Projects with a potentiometer
- NeoPixel projects
- Projects with a DHT11 or DHT22 sensor
- Projects with a piezo speaker
- OLED display projects
- Projects with a transistor
- Arduino game projects
- Robot projects for Arduino and ESP32
- Home automation projects with ESP32 and Arduino
