Source: https://mokxi.com/ideas/d4184module-projects
Updated: 2026-11-17

Projects / Project ideas
Project ideas by part

# Projects with a D4184 MOSFET module

7 Mokxi projects use a D4184 MOSFET module (4 beginner and 3 intermediate). They run on Arduino Uno boards, and 1 needs no board at all. Here are all of them, from “3 W power LED on pin 13” to “Workbench light”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “3 W power LED on pin 13”, a beginner project that needs a D4184 MOSFET module, a resistor and a power LED.
- Arduino Uno runs 6 of them and 1 needs no board at all. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the filament lamp (1 project), the PIR motion sensor (1) and the potentiometer (1). With those on hand, most of this list is open to you.
- Before you build one on a real bench, open the D4184 MOSFET module part page for its pins and what each one does.

Projects

## 7 projects ready to run

### 3 W power LED on pin 13

A 3 W white power LED, switched by a MOSFET module whose trigger is on pin 13, blinks once a second from the Uno’s 5 V through a 4.7 ohm resistor.

Board

Arduino Uno R3

Parts

D4184 MOSFET module, resistor, power LED

Level

Beginner

Open in the simulator

### Aquarium air pump and doser

Two D4184 modules on pins 9 and 10 run a 12 V air pump all the time and a peristaltic pump for 3 s, 5 ml, every 20 s.

Board

Arduino Uno R3

Parts

DC jack and adapter, D4184 MOSFET module, mini water pump

Level

Beginner

Open in the simulator

### Motion alarm siren

A PIR on pin 2 trips a 12 V alarm siren on a D4184 MOSFET module for ten seconds, then the alarm waits for quiet and re-arms.

Board

Arduino Uno R3

Parts

PIR motion sensor, D4184 MOSFET module, alarm siren, DC jack and adapter

Level

Beginner

Open in the simulator

### 12 V lamp dimmer with a MOSFET module

A knob on A0 sets the PWM on pin 9, and a D4184 MOSFET module dims a 12 V lamp on a wall adapter with it: the pin switches the gates, not the lamp.

Board

Arduino Uno R3

Parts

Potentiometer, D4184 MOSFET module, DC jack and adapter, filament lamp

Level

Beginner

Open in the simulator

### IRF520 and D4184 MOSFET modules

One switch drives an IRF520 module and a D4184 module, each on a 12 V load: the IRF520 is half on from 5 V and off from 3.3 V.

Board

No board

Parts

Resistor, slide switch, IRF520 MOSFET module, D4184 MOSFET module

Level

Intermediate

Open in the simulator

### Peltier cooler with a MOSFET module

An Uno runs a TEC1-12706 Peltier module flat out for a minute through a D4184 MOSFET module on pin 9, then holds it at 60 % with PWM.

Board

Arduino Uno R3

Parts

D4184 MOSFET module, battery: AA, peltier module

Level

Intermediate

Open in the simulator

### Workbench light

A 3 W power LED spot flashes on pin 8 through a D4184 module, its 700 mA set by a 12 ohm 10 W resistor on a 12 V adapter.

Board

Arduino Uno R3

Parts

D4184 MOSFET module, resistor, power LED, DC jack and adapter

Level

Intermediate

Open in the simulator

Keep going

## Wiring, libraries and more ideas

The D4184 MOSFET module part page Every project ideas list

### More project ideas

- Arduino Uno project ideas
- Electronics projects with no code
- Projects with a lamp
- Projects with a PIR motion sensor
- Projects with a potentiometer
