Source: https://mokxi.com/ideas/circuits-without-code
Updated: 2026-11-17

Projects / Project ideas
Project ideas by board

# Electronics projects with no code

82 Mokxi projects have no microcontroller in them (49 beginner, 26 intermediate and 7 advanced). Here are 24 to start with, from “Operating point and sweep” to “Up/down counter”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “A divider, measured”, a beginner project that needs a resistor and a multimeter.
- Most of them are beginner projects. Pick one a level below what you think you can do, finish it, then move up.
- The parts used most here are the LED (32 projects), the capacitor (20) and the slide switch (15). With those on hand, most of this list is open to you.
- With no microcontroller, the simulator solves the circuit itself, so a changed resistor or capacitor shows its effect the moment you press Run.

Projects

## 24 projects of 82

### Operating point and sweep

A 10 k divider and a 10 k / 10 uF RC on one board, for reading every node at once and sweeping the supply or a resistor.

Board

No board

Parts

Resistor, capacitor

Level

Beginner

Open in the simulator

### ULN2803A switching four 12 V lamps

Four slide switches on a ULN2803A's inputs, four 12 V lamps on its outputs: each channel sinks its lamp to about 0.87 V.

Board

No board

Parts

ULN2803A Darlington array, slide switch, filament lamp

Level

Beginner

Open in the simulator

### Plus and minus 5 V

Two 12 V sources make a split supply, and a 7805 and a 7905 turn it into +5 V and -5 V, each with a load on it.

Board

No board

Parts

DC voltage source, voltage regulator, resistor

Level

Beginner

Open in the simulator

### USB to 3.3 V

A USB-C breakout on a computer port feeds an AP2112K-3.3 low dropout regulator, which lights an LED at 3.3 V.

Board

No board

Parts

USB power, voltage regulator, resistor, LED

Level

Beginner

Open in the simulator

### A divider, measured

Three resistors from 5 V to ground with a multimeter on the taps: volts, amps, ohms and continuity on the simplest circuit there is.

Board

No board

Parts

Resistor, multimeter

Level

Beginner

Open in the simulator

### BCD display

Four DIP switches set a number in binary and a CD4511 shows it as a digit on a seven-segment display.

Board

No board

Parts

4-way DIP switch, 4-resistor network, CD4511 7-segment driver, seven-segment display, resistor

Level

Beginner

Open in the simulator

### NE556 two blinkers

The two 555 timers in one NE556, each an astable with its own LED: 1.5 Hz and 3.2 Hz from one chip on one 5 V supply.

Board

No board

Parts

NE556 dual timer, resistor, capacitor, LED

Level

Beginner

Open in the simulator

### LM317 adjustable supply

An LM317 on a 12 V adapter with 240 ohms and a 2 k pot: Vout = 1.25 V x (1 + R2/R1), from 1.25 V up to the dropout, with an LED on the output.

Board

No board

Parts

DC jack and adapter, LM317 regulator, resistor, potentiometer, LED

Level

Beginner

Open in the simulator

### 74HC decoder, mux and adder drawer

12 chips on breadboards, powered, every input tied low and ready to rewire.

Board

No board

Parts

74HC147 priority encoder, 74HC148 priority encoder, 74HC151 8-input multiplexer, 74HC153 dual 4-input multiplexer, 74HC157 quad 2-input multiplexer, +7 more

Level

Beginner

Open in the simulator

### NPN transistor switch

A 2N2222 switching an LED from a slide switch through a 1 k base resistor, with real Gummel-Poon currents in the base and collector.

Board

No board

Parts

Resistor, LED, transistor, slide switch

Level

Beginner

Open in the simulator

### What is this part?

Two component testers with unknown parts in the sockets: one names a transistor and finds its base, collector and emitter.

Board

No board

Parts

Transistor, LED, component tester

Level

Beginner

Open in the simulator

### Doorbell

A pushbutton lifts the 555 out of reset and a 4 Hz astable beeps the buzzer.

Board

No board

Parts

Resistor, NE555 timer, capacitor, push button, buzzer

Level

Beginner

Open in the simulator

### TL072 amplifier on +-12 V

A TL072 inverting amplifier with a gain of -4.7 on a +12 V and -12 V supply: a 1 V sine in, a 4.7 V sine out, upside down and both sides of ground.

Board

No board

Parts

Function generator, TL072 dual JFET op-amp, resistor, oscilloscope

Level

Intermediate

Open in the simulator

### Dark detector

An op-amp comparator, an LDR and a pot light an LED when the room goes dark, no board, on a half-size breadboard.

Board

No board

Parts

Photoresistor, resistor, potentiometer, op-amp, LED

Level

Intermediate

Open in the simulator

### JK flip-flop counter

Two JK flip-flops in a 74HC112 toggle on each falling clock edge and count 0 to 3 in binary on two LEDs.

Board

No board

Parts

Clock, 74HC112 dual JK flip-flop, resistor, LED

Level

Intermediate

Open in the simulator

### Counting clock

A program counter built from NAND gates, counting one step clock tick at a time, with its LOAD tied to 0 by a constant bit.

Board

No board

Parts

Number switch, constant bit, bit switch, step clock, logic gate, +1 more

Level

Intermediate

Open in the simulator

### Switch shifter

A 74HC165 loads an 8-way DIP switch at the press of a button and clocks the byte out one bit a second onto an LED.

Board

No board

Parts

Clock, push button, resistor, 8-way DIP switch, 8-resistor network, +2 more

Level

Intermediate

Open in the simulator

### BSS138 level shifter

One channel of the bi-directional 3.3 V to 5 V level shifter: a BSS138 and two 10k pull-ups. Pull either side low and the other follows.

Board

No board

Parts

MOSFET, resistor, slide switch, multimeter

Level

Intermediate

Open in the simulator

### LM339 window comparator

Two LM339 comparators with their open-collector outputs wired together light one LED whenever a knob leaves the window from 1.67 V to 3.33 V.

Board

No board

Parts

Potentiometer, LM339 quad comparator, resistor, LED

Level

Intermediate

Open in the simulator

### Op-amp amplifier, gain of 10

An inverting op-amp amplifier on a single 5 V supply: a 0.2 V sine in, a 2 V sine out, upside down, with clipping and a frequency response to explore.

Board

No board

Parts

Function generator, resistor, op-amp, oscilloscope

Level

Intermediate

Open in the simulator

### NAND latch

Two cross-coupled 74HC00 gates hold one bit, and a slide switch sets and resets it.

Board

No board

Parts

Slide switch, 74HC00 quad NAND, resistor, LED

Level

Intermediate

Open in the simulator

### Five StepStick drivers left alone

TMC2208, TMC2209, TMC2100, DRV8834 and DRV8880 on one 200 Hz clock each: left alone, each steps at its own default resolution.

Board

No board

Parts

TMC2208 stepper driver, NEMA 17 stepper motor, clock, TMC2209 stepper driver, TMC2100 stepper driver, +2 more

Level

Intermediate

Open in the simulator

### Full adder

Three 74HC chips add two bits and a carry, with the sum and carry on LEDs.

Board

No board

Parts

Slide switch, 74HC86 quad XOR, 74HC08 quad AND, 74HC32 quad OR, resistor, +1 more

Level

Advanced

Open in the simulator

### Up/down counter

A slide switch and a 74HC02 steer a clock into a 74HC193, which counts up or down in binary on four LEDs.

Board

No board

Parts

Clock, slide switch, resistor, 74HC02 quad NOR, 74HC193 up/down counter, +1 more

Level

Advanced

Open in the simulator

See all 82 Electronics projects with no code projects on the templates page

Keep going

## Wiring, libraries and more ideas

The breadboard simulator Every project ideas list

### More project ideas

- LED projects for Arduino, ESP32 and Pico
- Projects with a capacitor
- Projects with a slide switch
- Projects with a potentiometer
- Projects with a 555 timer
- Projects with a push button
- Projects with logic gates
- Projects with a lamp
- Home automation projects with ESP32 and Arduino
- Arduino music and sound projects
