Source: https://mokxi.com/ideas/beginner
Updated: 2026-11-17

Projects / Project ideas
Project ideas by level

# Beginner electronics projects

A beginner project has one board, a few parts and a sketch short enough to read in one sitting. Mokxi has 425 projects at this level. Here are 24, picked across boards and topics. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “CircuitPython NeoPixel rainbow on a Pico”, a beginner project that needs NeoPixel LEDs.
- Arduino Uno runs 221 of them, Raspberry Pi Pico 65 and ESP32 55. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the LED (141 projects), the push button (64) and the potentiometer (31). With those on hand, most of this list is open to you.
- Do one project end to end, then change one thing in it (a pin, a delay, a color) and run it again before you move on.

Projects

## 24 projects of 425

### Comparator boards

An MQ-2, a flame sensor, a TCRT5000 and an FC-51, each lighting a lamp from DO with no board. The same LM393 under four sensors, and DO goes low.

Board

No board

Parts

MQ-2 gas sensor, flame sensor, TCRT5000 line sensor, FC-51 IR obstacle sensor, LED, +1 more

Level

Beginner

Open in the simulator

### UV index meter

A GUVA-S12SD UV sensor and a 16x2 I2C LCD: the UV index and how risky it is, from low to extreme. Drag the sunshine.

Board

Arduino Uno R3

Parts

UV sensor, I2C LCD

Level

Beginner

Open in the simulator

### MicroPython I2C LCD1602 on a Pico, GP14 and GP15

MicroPython on a Raspberry Pi Pico: an I2C LCD1602 on GP14 and GP15 shows a greeting on its first line and a counter that ticks every second.

Board

Raspberry Pi Pico

Parts

I2C LCD

Level

Beginner

Open in the simulator

### DevKitC blink

An LED on GPIO 2 of Espressif’s ESP32-DevKitC V4, which has no user LED of its own and covers the breadboard’s whole width.

Board

ESP32-DevKitC V4

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Morse sender

An ESP32-C3 sends a word in Morse on a lamp and a piezo at once, and a button picks the next message.

Board

ESP32-C3-DevKitM-1

Parts

Resistor, LED, piezo speaker, push button

Level

Beginner

Open in the simulator

### Nucleo fade

analogWrite breathes an LED on D9 of an STM32 Nucleo-F411RE, at STM32duino’s 1 kHz PWM.

Board

STM32 Nucleo-F411RE

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Blink an LED with RPi.GPIO

RPi.GPIO on a Raspberry Pi Zero 2 W: an LED on GPIO17 blinks twice a second, and the Serial Monitor counts every four blinks.

Board

Raspberry Pi Zero 2 W

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Pico W active buzzer beeps through an S8050

MicroPython on a Pico W: GP15 switches an S8050 that sounds an active buzzer: four short beeps, a pause of a second, and again.

Board

Raspberry Pi Pico W

Parts

Buzzer, transistor, resistor

Level

Beginner

Open in the simulator

### ESP32-C6 fade

Breathes an LED on GPIO 10 with analogWrite, so the waveform comes out of the LEDC hardware and the core sleeps between steps.

Board

ESP32-C6-DevKitC-1

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Pro Micro blink

A board with no LED on pin 13 blinks its RX lamp instead, with an LED on pin 9 beside it wired the ordinary way around.

Board

SparkFun Pro Micro

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### XIAO C6 knob

The XIAO ESP32-C3’s knob circuit, pad for pad, on the ESP32-C6: D0 is still A0, though the GPIO under it has changed.

Board

Seeed XIAO ESP32-C6

Parts

Potentiometer, resistor, LED

Level

Beginner

Open in the simulator

### PIR motion sensor with gpiozero

gpiozero MotionSensor on a Raspberry Pi 4: an HC-SR501 PIR on GPIO4 lights an LED on GPIO17 while something moves, and counts each movement.

Board

Raspberry Pi 4 Model B

Parts

Resistor, LED, PIR motion sensor

Level

Beginner

Open in the simulator

### LOLIN32 Lite button

A pushbutton on GPIO 4 lights the LOLIN32 Lite’s blue LED on GPIO 22, which comes on when its pin is LOW.

Board

Wemos LOLIN32 Lite

Parts

Push button

Level

Beginner

Open in the simulator

### RP2040-Zero blink

An LED on GP0 of the RP2040-Zero, which has no plain LED of its own, with the board beside the breadboard.

Board

Waveshare RP2040-Zero

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Electronic voting machine

Electronic voting machine on an Arduino Nano: four buttons to vote, a result button for every count and the winner on an LCD.

Board

Arduino Nano

Parts

Arcade button, piezo speaker, I2C LCD

Level

Beginner

Open in the simulator

### Pocket gaussmeter

A 49E linear Hall sensor on A0 and a 16x2 I2C LCD: the field in gauss, which pole it is, and the strongest seen since power on.

Board

Arduino Uno R3

Parts

49E linear hall sensor, I2C LCD

Level

Beginner

Open in the simulator

### CircuitPython NeoPixel rainbow on a Pico

CircuitPython on a Raspberry Pi Pico: Adafruit’s neopixel library turns a rainbow around eight WS2812 LEDs on GP16, sent by the Pico’s PIO.

Board

Raspberry Pi Pico

Parts

WS2812 NeoPixel LEDs

Level

Beginner

Open in the simulator

### CD4000 counter, switch and one-shot drawer

13 chips on breadboards, powered, every input tied low and ready to rewire.

Board

No board

Parts

CD4027 dual JK flip-flop, CD4013 dual D flip-flop, CD4020 14-stage counter, CD4040 12-stage counter, CD4024 7-stage counter, +8 more

Level

Beginner

Open in the simulator

### ESP32 web server with two LEDs

The Random Nerd Tutorials ESP32 web server: press Run, open the Web panel, and its ON and OFF buttons switch the LEDs on GPIO 26 and 27.

Board

ESP32 DevKit V1

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### Micro blink

The Arduino Micro’s RX lamp, which lights when its pin goes low, blinking beside an LED on pin 9 that lights when it goes high.

Board

Arduino Micro

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### ATmega328P on a breadboard

The Uno’s chip on its own in a breadboard, wired as the tutorial wires it: 5 V on VCC and AVCC, both grounds, RESET held high, and an LED on PB5.

Board

ATmega328P, 16 MHz crystal

Parts

ATmega328P, resistor, LED

Level

Beginner

Open in the simulator

### ESP32-C3 PWM fade

Breathes an LED on GPIO 4 and the on-board one on GPIO 8 with analogWrite.

Board

ESP32-C3-DevKitM-1

Parts

Resistor, LED

Level

Beginner

Open in the simulator

### A button toggles an LED with gpiozero

gpiozero on a Raspberry Pi 4: each press of a button on GPIO2 turns the LED on GPIO17 on or off, with when_pressed and signal.pause().

Board

Raspberry Pi 4 Model B

Parts

Resistor, LED, push button

Level

Beginner

Open in the simulator

### D1 mini blink

The module’s blue LED on D4 lights when the pin is low and an LED on D1 when it is high, so the two are always opposite.

Board

Wemos D1 mini

Parts

Resistor, LED

Level

Beginner

Open in the simulator

See all 425 beginner projects on the templates page

Keep going

## Wiring, libraries and more ideas

Guides and tutorials on /learn Every project ideas list

### Wiring guides

- LED to Arduino Uno
- LED to Raspberry Pi Pico
- LED to Arduino Nano
- I2C LCD to Arduino Uno
- I2C LCD to Raspberry Pi Pico
- I2C LCD to Arduino Nano
- I2C LCD to ESP32
- push button to Arduino Uno

### Library pages

- LiquidCrystal I2C library

### More project ideas

- Arduino Uno project ideas
- Raspberry Pi Pico project ideas
- ESP32 project ideas
- Electronics projects with no code
- LED projects for Arduino, ESP32 and Pico
- Projects with an I2C LCD
- Projects with a push button
- Projects with a piezo speaker
- Arduino game projects
- Robot projects for Arduino and ESP32
- Home automation projects with ESP32 and Arduino
- IoT project ideas for ESP32 and Pico W
