Source: https://mokxi.com/ideas/arduino-uno
Updated: 2026-11-17

Projects / Project ideas
Project ideas by board

# Arduino Uno project ideas

566 Mokxi projects run on an Arduino Uno (221 beginner, 258 intermediate and 87 advanced). Here are 24 to start with, from “Button on pin 12 lights the LED on pin 13” to “Arduino quadruped robot”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

## How to pick your first one

- Start with “Arcade lever”, a beginner project that needs an arcade joystick lever.
- Most of them are intermediate projects. Pick one a level below what you think you can do, finish it, then move up.
- The parts used most here are the LED (142 projects), the push button (140) and the piezo speaker (83). With those on hand, most of this list is open to you.
- The Uno is the board most tutorials assume, so whatever you learn here carries over to books, kits and forum answers.

Projects

## 24 projects of 566

### Button on pin 12 lights the LED on pin 13

A pushbutton from 5 V to pin 12, held low by a 10k pull-down, lights the Uno’s own LED on pin 13 while it is pressed.

Board

Arduino Uno R3

Parts

Push button, resistor

Level

Beginner

Open in the simulator

### Thermocouple

A K-type thermocouple on a MAX6675 board, read twice a second with Adafruit’s max6675 library, in Celsius and Fahrenheit.

Board

Arduino Uno R3

Parts

Thermocouple converter

Level

Beginner

Open in the simulator

### Uno R4 knob

A potentiometer on an Uno R4’s A0 fades an LED on pin 9, and the monitor prints the same pin in ten bits and in the converter’s own fourteen.

Board

Arduino Uno R4 Minima

Parts

Potentiometer, resistor, LED

Level

Beginner

Open in the simulator

### Steam sensor on A0

A steam sensor’s output on A0, printed twice a second: the reading rises as steam or a breath fogs its comb of bare traces.

Board

Arduino Uno R3

Parts

Steam sensor

Level

Beginner

Open in the simulator

### Uno R4 WiFi heart

A heart beating on the Uno R4 WiFi’s 12 x 8 LED matrix, drawn through Arduino_LED_Matrix.h with no parts to wire.

Board

Arduino Uno R4 WiFi

Parts

Just the board

Level

Beginner

Open in the simulator

### Motor pinwheel

Hold the button and an IRF520 MOSFET on pin 9 runs a DC motor from a 9 V battery, with a 1N4007 across the motor to catch its kick.

Board

Arduino Uno R3

Parts

Push button, resistor, MOSFET, diode, DC motor, +1 more

Level

Beginner

Open in the simulator

### Object counter with an E18-D80NK

An E18-D80NK infrared sensor on pin 2 with the pin’s pull-up: each object that passes adds one to the count on a 16x2 I2C LCD, with a beep.

Board

Arduino Uno R3

Parts

E18-D80NK IR proximity switch, buzzer, I2C LCD

Level

Beginner

Open in the simulator

### IR remote codes on pin 12

An infrared receiver on pin 12: press a button on the remote and the IRremote library prints the code it sends.

Board

Arduino Uno R3

Parts

IR receiver and remote, IR remote

Level

Beginner

Open in the simulator

### Four-key keyboard

Four buttons share A0 through a ladder of 10k resistors, so each key reads a different number, and a piezo plays C, D, E or F.

Board

Arduino Uno R3

Parts

Push button, resistor, piezo speaker

Level

Beginner

Open in the simulator

### Arcade lever

A Sanwa-style arcade lever on four pins, debounced the way a stick board does it and printed in numpad notation: 5 neutral, 8 up, 9 up-right.

Board

Arduino Uno R3

Parts

Arcade joystick lever

Level

Beginner

Open in the simulator

### Water meter

A YF-S201 flow sensor’s pulses counted on an interrupt: 450 make a liter, and an I2C LCD shows the flow and the liters so far.

Board

Arduino Uno R3

Parts

Water flow sensor, I2C LCD

Level

Beginner

Open in the simulator

### Ofrenda candles

Six LED candles for a Día de los Muertos ofrenda, one for each person remembered: a button lights one at a time.

Board

Arduino Uno R3

Parts

Resistor, LED, push button

Level

Beginner

Open in the simulator

### IBT-2 BTS7960 big motor driver

An IBT-2 on pins 5, 6 and 7 ramps a 12 V motor off a lead-acid battery forward and back with analogWrite, then lets it coast.

Board

Arduino Uno R3

Parts

IBT-2 BTS7960 motor driver, DC motor, battery: AA

Level

Intermediate

Open in the simulator

### Desk clock

A DS3231 over I2C and a TM1637 on two wires that are not I2C.

Board

Arduino Uno R3

Parts

DS3231 real-time clock, TM1637 four-digit display, logic analyzer

Level

Intermediate

Open in the simulator

### An ESP32 and an Arduino Uno talking over serial

An ESP32 reads a knob and sends the number to an Arduino Uno over a serial wire; the Uno sets an LED’s brightness from it.

Board

ESP32 DevKit V1 and Arduino Uno R3

Parts

Potentiometer, resistor, LED

Level

Intermediate

Open in the simulator

### Touch paint

Draw on a 2.8 inch TFT with its resistive touch panel: two SPI chips on one module, and the raw touch counts mapped to pixels.

Board

Arduino Uno R3

Parts

Touch TFT

Level

Intermediate

Open in the simulator

### Radar sweep: ultrasonic on 10 and 11, servo on 12

An HC-SR04 (TRIG 10, ECHO 11) rides a servo on pin 12 that sweeps from 15 to 165 degrees and back.

Board

Arduino Uno R3

Parts

HC-SR04 ultrasonic sensor, servo motor

Level

Intermediate

Open in the simulator

### New Year's countdown

A DS3231 and a four-digit display count down to midnight on New Year’s Eve.

Board

Arduino Uno R3

Parts

DS3231 real-time clock, TM1637 four-digit display, resistor, WS2812 NeoPixel LEDs

Level

Intermediate

Open in the simulator

### Robot arm with joysticks

A four-servo desktop arm on four Uno pins, steered by two joysticks with the Servo library: base and shoulder on one stick.

Board

Arduino Uno R3

Parts

Four-servo robot arm, joystick

Level

Intermediate

Open in the simulator

### Joystick bar graph

A thumb stick moves a bar along eight LEDs, and pressing the stick swaps the bar to the other axis.

Board

Arduino Uno R3

Parts

Joystick, resistor, LED

Level

Intermediate

Open in the simulator

### Bluetooth lamp

An HC-05 modeled as what it is to the board: a serial bridge whose far end is the serial monitor. Type on or off and the lamp answers.

Board

Arduino Uno R3

Parts

HC-05 Bluetooth module, resistor, LED

Level

Intermediate

Open in the simulator

### Two boards, one wire

An ESP32-C3 pulses a number down one wire and an Arduino Uno counts it back out on the serial monitor.

Board

ESP32-C3-DevKitM-1 and Arduino Uno R3

Parts

Resistor, LED

Level

Advanced

Open in the simulator

### Pocket pet

A Tamagotchi-style pet on a 128x64 OLED: hatch it, feed it, play two mini-games, clean up, and it remembers you after a reset.

Board

Arduino Uno R3

Parts

SSD1306 OLED display, push button, piezo speaker

Level

Advanced

Open in the simulator

### Arduino quadruped robot

Eight servos on a PCA9685 walk a four-legged robot through a creep gait: one foot lifts and swings forward at a time while the other three hold it up.

Board

Arduino Uno R3

Parts

Servo driver, servo motor

Level

Advanced

Open in the simulator

See all 566 Arduino Uno projects on the templates page

Keep going

## Wiring, libraries and more ideas

The Arduino Uno R3 board page Every project ideas list

### Wiring guides

- LED to Arduino Uno
- push button to Arduino Uno
- push button to ESP32
- buzzer to Arduino Uno
- buzzer to ESP32
- I2C LCD to Arduino Uno
- I2C LCD to ESP32
- potentiometer to Arduino Uno

### Library pages

- LiquidCrystal I2C library
- Servo library
- Adafruit NeoPixel library
- Adafruit GFX library
- LiquidCrystal library
- IRremote library

### More project ideas

- ESP32 project ideas
- LED projects for Arduino, ESP32 and Pico
- Projects with a push button
- Projects with a piezo speaker
- Projects with an I2C LCD
- Projects with a potentiometer
- Servo motor projects
- Projects with a buzzer
- Projects with a DC motor
- Arduino game projects
- Robot projects for Arduino and ESP32
- Home automation projects with ESP32 and Arduino
